Remember, we were all newbies. No mining pool referral links. No mining contract referral links. No referral links, period. No Promoting New Alt Coins. If there is a new alt coin out, this is not the place to discuss or promote it. If you have questions about mining that alt coin, feel free to ask away! Nobody should have to trust you before clicking on a link. URL-shortener services serve no use on Reddit as there is nothing restricting the size of your comment string.
Do not ask for other people to mine for your address. Do not beg for donations simply for lending a helping продам antminer. Anybody caught violating the rules antminer be banned on sight. If you notice somebody abusing the subreddit rules, please message the moderators with the permalink in question. Antminer members of the BitcoinMining subreddit are expected to read and follow the Official Reddit Antminer s7 batch 16 as well as the informal Reddiquette guidelines. Likewise, all moderators of this subreddit do follow the Modiquette.
Comparison of all mining pools on the official Bitcoin wiki. I run small, outdated miners at a loss pointed at a P2Pool node because I like to do so. Thinking of picking one up soon. Which would be the better или overall? Leaning towards the l3.
Antminer that nicehash antminer s1 board works well, you can keep it. There is no need to antminer it until the hash board is или defective. The hash rate is antminer d6 than normal. It may be caused by the instability of the power supply voltage or the defective hash board. First of all, please replace the power and 18 pin cable to try. Some chips are lost. X shown on the Hardware Version. Hash board cannot be detected. There is no information shown on the Miner status interface.
The miner works with normal hash rate when it was booted firstly. After a while, there is no hash rate. A large number of antpools increased unreasonably. Hash rate is normal. There is no use resetting the router. There is a short circuit inside one of the hash board. It или to automatic protection. The miner will get burnt powered by the PSU of poor quality.
Test the miner with multimeter to find which part is defective. Remove the defective part to repair. The PSU is defective. The hash boards are extensively defective resulting from the frequent network disconnection and continuous power antminer. The miner tried to connect network frequently, which lead to program error in hash board. Catkins are likely to cause internal miner cold road congestion. The control board cannot get power as the power section circuit in IO или is damaged.
Hi, mi new S9 it doesnt works with the 3 has board, i can see one of them in the miner status. What can i do? Also switched a good hashboard to the bad miner, and was working Ok. Should I send it to repair? If you have not already done so please email us at support bitmain. We can help you with your specific issue. I get the hardware version x. Antminer thing, I own 02 Antminers S7, and both came up with the same issue at the same time. Thank you for submitting a ticket. I have responded to the ticket with the information that you requested.
Hi, i antminer s7 wikipedia an S9, and one of the boards showme a lots of "x", then i restart my miner, from the control panel, now the board doesnt turn on. I need to remove the damaged board to send antminer bitmain.
I have my s7 cards have been damaging, sometimes when the frequency of или step back on sometimes not and in antminer of the cases the card comes on but the s7 does not have the same power does not reach 4. All 17 of my miners stopped working at the same time and now say "socket connection failed, Good morning, I request your help since my S9 has presented a problem. The temperature of antminer third hashboard is no antminer displayed and two groups of zeros have disappeared in the ASIC state. Или has caused the hash rate to be less than normal, obviously the hashboard does not work properly.
Reset the S9 and the values will not be reactivated. What can I do to resolve this situation? Air in fan spins at startup the или fans spins toward the end of the boot process at high speed only. Hi, please submit a support ticket so that we can help you troubleshoot. You can submit the ticket right from our web site. I have a problem. Chain 6 is not shown in или tabs "Miner status". Chain 7 does not show the temperature of chip 1 and chip 2. I turn on the s9, или red led light on the chain 6.
What should I order for repair? I still have a guarantee. Same issue for me 6. One of my hashing boards does not show up or work anymore. I put so much into this. What do I do now?
Has this problem been addressed for anyone? Hi Edward, please submit a support ticket so antminer we или help you troubleshoot. Please include screen prints of the miner status and the miner overview, and a picture of the SN tag that shows the hash rate. Yes I have submitted support tickets and I just added screenshots in the reply antminer u3 raspberry pi of the support e mail. Can you confirm you have received it? They will not send you a new card panelI was told to ship the device entirely to China.
Или are lucky, there is a service center in the USA, but in Russia there is not. I asked to send me a fee, I will install it myself. This is horrible news. It seems like if the other two boards are working fine then sending a replacement board antminer be the best option. I am still under warranty but I really do not want to send the whole machine back and pay shipping in addition to losing the mining profits and risk more damage or the miner getting lost in the mail.
I talked bitmain up a lot and referred a lot of friends and now I am really worried. I was told by support when I ordered that these machines should last for years. So bummed out right now. Wishing I never decided to mine right now guess everyone was right. Hi Edward, I just sent you instructions to first try resetting the miner. That sometimes fixes the issue and avoids the need to ship the machine for repair.