Config antminer s1

Your problem is more than likely in the PSU.

config antminer s1

Make sure you are not using the thin loose wire or paperclip for this If the Jumper Cable is jammed in and set correctly, it could be your power supply unit. I understand that you could be using the W or even W PSU but it may not be strong enough to do the job. Disconnect all the power cables from the 2nd Blade. Then Power On the AntMiner.

config antminer s1

If you really want to test out the 2nd Blade, then replace the 1st Blade with the 2nd Blade. By the network cable port, there are 2 white plugs.

How to Setup an Antminer S1Bitcoin Miner – domsteil

Make sure antminer are connected to the 2nd blade If its power on, then the problem is for sure in your PSU. The oil can be very hard to see. You should use the reflection of a light to determine where the clear oil is on the circuit board. Do your best to clean it up. We clean up all thermal paste that we can get to, because when the device heats up under use, it will tend to run down the circuit board if there is much of any left on the circuit board. So, clean config you can, and check the device after 10 minutes of run time to make sure more paste did not sneak out from the screw holes. Now, placement of the S1 is important.

Antminer into each blade. There should be a 6-pin input female connector in the config center of each blade.

[Setup & Troubleshoot] Bitmain AntMiner S1 GH/S miner

Now, with your power connected but not turned on yetplug in your Ethernet cable. I have not personally confirmed this myself, but there may be a reason to antminer via Ethernet cable. Wait approximately 45 seconds after turning the power on before deeming everything as stable. We wait, because mining does not actually begin for approximately seconds after turning the device on. If all is well so far, it is time to connect to your AntMiner S1 and configure it. Log into a computer on the same network as your AntMiner S1. Obtain the IP address of the S1 -- it should be on a sticker near the main fan. Most devices seem to have I will show you how to change the Config address shortly. Load up your Internet browser I recommend Configand navigate to http: You ibelink или antminer be taken to a login screen.

Click on "Miner Configuration" Next, configure your pools. Click "Save and Apply" when you are done configuring your pools. The antminer software will automatically reset. You do not need to reboot the device.

config antminer s1

Click on the "Miner Status" tab. XXX, so you can browse the control panel.

[Setup & Tutorial] btc miner AntMiner S1 GH/s bitcoin miner asic miner for bitcoin mining

This is very similar to other OpenWRT based miners. Потребление antminer s9 user name and password: The LAN is useless for users, but only useful to developers. If you forget, you antminer not be able to login into the miner.

Just Antminer to Hashnest. Yes, if you use less wire, config to make sure you are config taxing all the energy into those wires. You can run it with config wire each, but distribute the energy to less tax each line is recommended. This is not the only way to set it up and you can tweak the setup as you please, but please do it safely!

Are they currently being distributed only for evaluators, or are they out now and I missed it somehow? BTW, sushi, thanks for the info and pics antminer your trip. Monitor all your miners in one place!

Похожие статьи:

  • Как заказать antminer на bitmain
  • Bitmain antminer d3 официальный сайт
  • Msi computer gtx 1080 gaming x 8g
  • Bitmain antminer s5 купить
  • Antminer s9 окупаемость калькулятор учитывая сложность
  • Geforce gtx 1060 armor 6g ocv1 цена

  • Рекомендуем почитать:

  • antminer s7ln купить
  • - 2018 (c)