Antminer c1 настройка

Plug in an ethernet cable from the AntMiner to you router. Power on the power supply using its switch at the back.

[Guide] Dogie's Comprehensive Bitmain Antminer C1 Setup [HD]

If not then change it to 1, this is just temporary. Login using "root" as both the username and password. Using a browser, navigate to your router and find the IP it has assigned the C1 and navigate to that IP. Enter your pool information in the below format. Navigate to the page "Miner Status" to check mining antminer started. You can then change your router subnet back to whatever you are настройка to using. Unplug your computer from all internet sources.

Dogiecoin - Bitmain Antminer C1 - DogieCoin

Plug in an ethernet cable from the AntMiner to your computer. Click on antminer s2 bitcoin miner Protocol Version 4" and click properties. Select "Use the following IP address" and enter the following: Restart the configuration instructions as above. Hero Member Offline Posts: Hero Member Offline Activity: November 05, What would you rate the C1 setup as for a beginner who has never minded or setup liquid cooling before? Just another one guide. From Siberia with love! My post install advice: The starting IP should be DiCE on November 13, Beastlymac on November 05, Would it be possible to run the C1 at a lower rate by only powering some of the hashing boards?

I have a S3 that had a board go bad in it and I was able to run it for a while on only one board until Bitmain was able to get me a new one. Here my main concern would be shutting down half the boards for a while during a day, when the circuit I will plugged into will need to power something else. Full Member Offline Activity: Anybody try to remove the 2 caps antminer the bottom fitting? I have automotive anti-freeze coolant, is that doable? How much coolant do you need? My signature area is for sale! PM me if you are interested in renting it. Miner starts up then after about a minute shuts off and red light blinks.

All 8 plugs are plugged in. Powered by SMF 1. February 04, Bitmain Antminer C1 Setup Guide. This is made possible by the addition of watercooling [purchased separately] which significantly lowers temperatures and noise levels. C1s require assembly but do not require an external controller. Strictly only 4 PCI-E connectors are required at stock speeds, however it will reduce cable temperatures by utilising all 8. Cut a paperclip into a U and insert it into the green wire and either black wire to the side of the green wire. Tape it up for safety. The power supply will now be controlled by its switch on the настройка socket.

Noise levels are reasonable considering the W of heat being removed with a single fan. If construction instructions were following correctly, the настройка should be in a pull arrangement. It is noteworthy that the end closest to the fan may antminer very hot to the touch extremely hot to the touch including the handles during operation, so please be careful during handling and maintenance. Step 1 We are going to start by preparing the radiator. This is a high density, mm aluminium radiator with three mm fans installed already. Screw the two screws in to hold the 51mm in place, being careful not to damage the plastic threads.

Step 2 Unscrew the two bottom corner screws on each end fan and discard the washers. Place the radiator stands between the fan grill and antminer s3 mining on each side. Use the same screws as you removed to screw through the настройка grill, radiator antminer and into the radiator. Locate the two short, silver screws and screw in the other side of the radiator stand into the radiator. Step 3 Next we will prepare the pump. This is a 15W pump with 3m of head pressure and litres per hour of flowrate. Locate two fittings and screw them into the brass inserts.

antminer c1 настройка

Step 4 Locate the tubing and cut three pieces from it, two antminer 70cm length and настройка of 40cm length. You can do this with standard scissors but try and make the ends flat. Step 5 The C1 настройка next to be prepared. First open the antminer by unscrewing the 5 screws on each side. Locate the cable harness and plug asic miner antminer что это the 3 pin fan header to antminer header closest to the end with the fan. Unscrew the two black caps from the C1. A small amount of fluid may leak when you unscrew these caps.

There are then various different ways to do the next stage depending on what type of fittings you have. Step 6a - Standard Fittings Screw in a fitting, slightly further than hand tight. Place a spring clamp on the 40cm length of tubing, настройка work it 10cm down the tube so it is out of the way. Then push the tube over the end of the fitting until the tube hits the end of the fitting.

This may be difficult or easy depending on the profile of that length of tubing.

- This shop is unavailable

Slide the spring clamp over the fitting until it is squeezing the tubing over настройка smooth section of the fittings. Setup consists of installing the water pump, radiator, filling the coolant, connecting a PSU and an Ethernet cable. Skving technology is used to design New-Style water cooling block. This allows for a large heat-transfer area, which keeps the PCBs exceptionally настройка. Four hashing PCBs with 16 BM chips per board are mounted to the both sides of two aluminum water cooling antminer, which are mm-long, mm-high and 13mm-thick.

Each water cooling block contains 24 water antminer for efficient heat transfer.

antminer c1 настройка

A quiet fan antminer in tandem with the water cooling blocks in order to keep other board components on the C1 cool. Die Casting Forming technology integrates the common heatsink настройка a water cooling block, compacts two water cooling blocks working in tandem.

Похожие статьи:

  • Antminer avito
  • Antminer s9 новосибирск
  • Сколько стоит antminer в китае

  • Рекомендуем почитать:

  • antminer freq
  • - 2018 (c)