Once done, you can go to the miner config page and set your pools. You can also set the S3 to failover or to perform load balancing for pool management. The setting is convenient as you can use multiple pools at once. Bitmain listened to many in the mining community that mention the S1 could be miner cooled with a cowl on it. The S3 has a cowl over the blades antminer s1 asic dual fans.
The cowl allows for very efficient cooling. The fans, despite there being two of them, were actually not as loud as my S1. My S3 ran at 42 to degree Celsius. In contrast, my S1 runs between 47 and 50 Celsius. Bitmain has focused on making the S3 as efficient as possible. Accuracy has been tweaked so hardware error rates are as low as. The S3 is super easy to use as usual. Bitmain did not cut any corners. The new design helps show off the new chips. I am sure that the OC masters in the community will be able to push it even further. I have to stress the build quality again is amazing. It is antminer yet built solid. Each blade has an aluminum heatsink on the front that is large also one on the backside of the board miner is all set in the cowl in such a way as to miner the best heat exchange.
You can use any Raspberry Pi for this tutorial. You need to know those things first before you can watch this video. Now if you know how to do all that stuff then you are antminer что такое майнер antminer s9 go and you could follow with this video.
You could find out by typing, if antminer in the terminal when Raspbian is loaded and it should show you your IP address.
So, now we are just going to click open here and it should start, click on yes. It should start loading the Raspberry Pi. You can use any Raspberry Pi you want and it should work. Now the first thing we need to do is copy the first line of code here sudo apt-get update copy this. Then hit enter and let it run. Copy that and paste it here and then hit enter. And it should prompt you to continue with Y for yes N for no. Type Y then hit answer. Now we are going to install dependencies. To do that, copy this code here from sudo and up until the screen here.
Copy all that and paste it miner, hit enter and it should prompt you to continue Y for yes N for no. Type Y hit enter. Copy it and paste it on the terminal and hit enter. Copy that and paste it and hit enter. Antminer this and paste it on here then hit enter and give it a couple of miner.
Copy this and paste antminer on to here then hit enter. Copy it, paste it here and hit enter. And now everything is installed.
Now we could test out whether or miner it will work. Now you need to fill in the blanks here. Your pool you need to — miner it says pool here you need to fill antminer in with your pool address and where it says username you need antminer fill it in with your username and where it says password here you need to fill this in with your password. I opened up my text document here and I pasted that onto a text document. You should paste it onto a text document and save it onto your desktop so that you could just copy it and paste it onto a terminal at any time whenever you want to run your замена кулера на antminer. This is my pool url.
I replaced my user with my username. My username is rasim. Remember first thing you do is copy this here. This bit of code here and copy it and miner it in a antminer editor, note pad or whatever you want to do. Then paste or replace the pool with your pool address, the username with your worker name and the password with your password and then miner it onto the desktop so you could just easily copy it and paste it when you need to.
Remember it can be filled in with your info, your pool address, your worker username and your worker password. So, now all we have to do — and when you paste this it has to be in the CG Miner directory — cd to the root directory hit antminer. You have to be in the CG Miner directory before you can paste this code.
Miner here is how many gigahash or megahash you are running per second up here. So again to exit all you have to do is type in Q. Hit Q and it should shutdown. And it should go back to terminal. So all antminer have to do is just copy the code and just paste it and it miner start mining. Again you antminer to be in the CG Miner directory. Then you could open up your text document and copy the code that will automatically start CG Miner and start mining for you then hit enter and it should start working.
If you guys like this video please give me a like.